LCD V3 Screen Replacement Kits for Nintend GBA backlight lcd screen 10 Levels High Brightness IPS LCD V3 Screen For GBA Console. Heat your soldering iron and add a little flux to each of the pads if you have any. Just sink them in and put the rubber membranes on top once done like below. Your email address will not be published.
Grab your replacement GBA IPS screen lens and remove the adhesive tape on the back.
Place the front half of the shell face down. This is optional as the IPS will default to a mid-brightness. Now that we have our soldering finished, we can start to put everything back together. Add some flux to your points and you really only need a tiny amount of solder. Anterior shell × 1 In the past we have had GBA backlight mod installs using screens from the backlit SP variant AGS-101. We want to solder from point Q12B to the point on the ribbon cable. Thank You! This can be done by gently flexing the shell until the screen ‘pops’ out. Flip your Game Boy Advance SP over and make sure your console is turned off and you have removed any game from the console. Next, install the 3 x Phillips head screws we removed earlier to fix the GBA motherboard back into place. This needs to come off both the bezel of the lens and clear viewable part. Any donations will go back into making more guides and reviews. You can tin your wire with a little flux and solder to make things easier and when ready just touch your hot soldering iron to the points. We want to connect the funny playing’s ribbon cable to the connector on the back of the screen. Free shipping . Lift out any remaining buttons and the speaker (It just lifts out!).
They are both very similar and if you're going for an overall brighter screen on your GBA they are both good options. If you want to support Cheaper Gamer you can donate via PayPal here. Now, we need to solder the ‘L’ & ‘R’ wires to the points below, with L being the left button and R being the right. GBA IPS screen (Comes with IPS screen, ribbon and self-adhesive tape), Soldering Iron (Needed for brightness controls only), Flush Cutters (If cutting original shell), Plastic Brackets (If using original shell), **You can pick-up a pre-modded Shell, IPS screen, Lens new buttons, screwdrivers etc all in one package here, you just need to provide a GBA**. We can now reinstall the power switch, L & R buttons and side pieces. We can now install all buttons, rubber pads and speakers back into place. Connect the ribbon cable to the motherboard port and hold the battery in place to test. Push it into place and we can finally put the GBA SP back together. The screen fits perfectly into the front half of the shell, you don’t need to add any spacer as you do in the GBA IPS mod.
Your email address will not be published. We going to be focusing on the motherboard next and will need to change over to a small Phillips head screwdriver. Once you have all three wires fixed into place, we need to begin soldering them to the motherboard. Game Boy Advance Shell Case Solid Green IPS Replacement GBA RetroSix ABS. GBA IPS screen (Comes with IPS screen, ribbon and self-adhesive tape) Tri-wing and Phillips head screwdrivers Optional (But recommended): Pre-cut shell. The best way, in my opinion, to play GBA games is on the GBA SP. Favorite Add to Gameboy Advance - Upgraded Funnyplaying LCD v2 Modded Console - Nintendo RetroVids. FunnyPlaying ship their screens in a rather fancy box, this is great as it affords a great deal of protection to the contents. Money Back Guarantee Carefully, line up the tape the with shell and remove the bottom part being sure to make sure none is overlapping with the viewable windowed in the middle. Gently pry the ribbon cable out of the connector and we will be able to completely separate the motherboard from the GBA shell.
Soldering Iron (Needed for brightness controls only) Wire.
$19.97. We remake old console hardware and parts for the new age. GBASP Ribbon V2 × 1 NOTES. shipping: + $7.76 shipping .
Now we are about to solder the included wire to allow us to control the brightness. Connect your cable into the GBA’s motherboard, shiny contacts should be facing towards you as you do this, and you’ll need to push down on the brown tabs once again to lock it into place.
We have recently come out with a newer Game Boy Advance modified console. With the screws out, gently lift up the motherboard to find the ribbon cable that is attached to the board. Screws × 1 Now, to install the GBA SP IPS screen either back into the original shell or into a replacement like I am doing. Line it up into place and pass the ribbon cable through the slot.
Install all the screws we took out and don’t forget the rubber pads around the screen bezel, they just push in. As an Amazon Associate I earn from qualifying purchases. We will need to trim the inside of the shell as outlined in the below picture.
They are easy to remove, they just slide off. shipping: + $7.76 shipping . $25.95. shipping: + $7.76 shipping . As you can see the IPS is much brighter, with better colours. This is very easy to do but might be a little time consuming if you are a perfectionist. Your email address will not be published.
If you get stuck during the reassembly process, please refer to that article but I will try to be as thorough as possible!
I used a pair of ESD tweezers and they came off just fine!
The GBA SP IPS Screen is far superior to even the AGS-101. First, up your will want to turn your Game Boy Advance over and remove any batteries installed. Game Boy Original Shell Case Solid Orange Replacement GB DMG … We always stock the very latest kits so this is . One last step before we can free the motherboard from the GBA’s housing, Locate the ribbon cable connector at the top of the motherboard. CUSTOMIZE GBA HOUSING Notify me of follow-up comments by email. If you want to support Cheaper Gamer you can donate via PayPal here. if you are reusing yours you have to be careful as they are quite fragile. Flush Cutters (If cutting original shell) Plastic Brackets (If using original shell) Now, on to the GBA SP IPS screen itself. On your ribbon cable, find the pads ‘SEL’ ‘R’ & ‘L’, we need to solder a wire from each of these points. Remove the remaining tape facing towards us, remove the plastic protective film on your GBA IPS screen by pulling down toward you. From shop RetroVids. Gather all the supplies you need for the mod. Add some batteries or a battery mod and turn it on. Just be sure to not dangle your wire across where any of the button pads are going to go. The Game Boy Advance is still my favourite handheld, even though the Switch is a good contender. Thanks to our soldering earlier, if we hold down select and press either ‘L’ or ‘R’ we will be able to increase or decrease the brightness. Made of high-quality materials, more rigid.